Peter Weil Geschrieben 12. Februar 2008 Teilen Geschrieben 12. Februar 2008 Hallo..... Bei meinem Whirlwind ( habe leider keine Unterlagen oder Schaltpläne für diese Pins ) sind beide Displays komplett ausgefallen. Tippe auf die Hochspannung Was könnte das Problem sein. Welche Sicherung ist dafür Zuständig. Woran könnte es noch liegen Vielen Dank und Gruß aus Frankfurt TOM Link zu diesem Kommentar Auf anderen Seiten teilen Mehr Optionen zum Teilen...
MAAA Geschrieben 12. Februar 2008 Teilen Geschrieben 12. Februar 2008 When thing don't work: Score Display Problems One of the most frequent system 11 problems relates to non-working or weak score displays. Fortunately, often there is a very easy fix for this problem. The simplest thing to check when the score displays do not work is the +100 and -100 volt DC power section of the power supply. If either of these voltages are bad, your displays will not work. And quite often, this power supply section does go bad. Replace the 39k ohm Power Supply Resistors. The major villain in the system 11 power supply are resistors R1 and R4. These are both 39k ohm, 1 watt resistors. Very often either or both of these resistors will go out of spec, or even completely open. This will prevent the +100 and/or -100 volts from getting to the score displays. These two resistors are mounted on the system 11 power supply board. (on newer WPC games with alphanumeric displays, these are resistors R48 and R49 on the alphanumeric display board). As a general rule, I always change these resistors (trust me, they've had a tough life, and need to be replaced, even if they test as "good"). If the high voltage fuses are not blown, and the score displays do not work, first replace the 39k ohm resistors. These are cheap and easy parts to replace (a lot cheaper and easier than replacing score display glass!) Or at least check these with a DMM. Replace these two resistors with "flame proof" 1 or 2 watt 39k ohm versions. And make sure to mount the new resistors slightly off the circuit board, so air can get under them for cooling. Note the score display is barely working. At first, you may think it's the display glass itself. This is infact a common problem, where the displays "outgas" and don't show as brightly, and eventually completely die. But before you change the expensive score display glass, change the 39k ohm resistors on the power supply with new 1 or 2 watt "flameproof" resistors. Gruß Andy Link zu diesem Kommentar Auf anderen Seiten teilen Mehr Optionen zum Teilen...
MAAA Geschrieben 12. Februar 2008 Teilen Geschrieben 12. Februar 2008 (bearbeitet) Hier noch das passende Bild, diese beiden Wiederstände auf dem Power Supply solltest messen. Quelle des Beitrag:marvin3m.com Bearbeitet 12. Februar 2008 von MAAA Link zu diesem Kommentar Auf anderen Seiten teilen Mehr Optionen zum Teilen...
Peter Weil Geschrieben 13. Februar 2008 Autor Teilen Geschrieben 13. Februar 2008 (bearbeitet) Hi... erst mal VIELEN DANK für deine Schnelle Hilfe. Werde mich am Wochenende mal hinstellen und die Teile Prüfen. Sobald ich mehr weiß, werde ich es hier schreiben. Gruß Tom ( Pittfall) Bearbeitet 13. Februar 2008 von Peter Weil Link zu diesem Kommentar Auf anderen Seiten teilen Mehr Optionen zum Teilen...
Empfohlene Beiträge
Erstelle ein Benutzerkonto oder melde Dich an, um zu kommentieren
Du musst ein Benutzerkonto haben, um einen Kommentar verfassen zu können
Benutzerkonto erstellen
Neues Benutzerkonto für unsere Community erstellen. Es ist einfach!
Neues Benutzerkonto erstellenAnmelden
Du hast bereits ein Benutzerkonto? Melde Dich hier an.
Jetzt anmelden